Видео

Isn't that an island?

You're absolutely right. Allow me to describe what actually happened and I settled for one actuator : When I finished shooting the assembly of the boat I was on a very tight schedule as I urgently had to visit the dentist at the end of the day. I had to make the necessary changes to correct any problems within three hours before my appointment and then partly disassemble the boat and fit everything in the car as wind speeds dropped the next day (just that day) and I had to go for launch. I managed to fix a problem with the paperplane not launching on a straight line and also balanced the ship using fishing weights. Balancing the boat was much more difficult than I expected as the bridge sat quite high and made the boat top heavy. I managed to complete everything with only a few minutes to spare and by the end of the day felt so tired I didn't have any energy left to fit a second actuator and add some details on the outside of the boat (railings, ropes, etc.) That's the price of having very little time to test and build... 🙁

😁

You've come to the right place then!

Me neither. I could have kept it flying for much longer if I didn't have to take control of the massive LEGO boat drifting away in the sea... 😁

😁

Мне нравится создавать вещи, которые двигаются. 😁

What is a mission without a crew... 😁

Swim...

@@brickandgear looks cold :/

@@throwawaypt2throwawaypt2-xp8nx it is...

Hello! I am currently building my second generation submarine. Expect a video soon!

Έχουμε πολύ ωραία σκηνικά για τέτοια βίντεο στην Ελλάδα! 😁

Obrigado! 🙏🙂

It's on my "To-do" list. I'll need more parts though.

A rover is definitely the next step.

I will probably experiment with model rockets in the winter. So, you can probably imagine what I have in mind... 😁

I wouldn't be able to sleep at night if I didn't manage that! 😁

😁

I won't use this setup again. Check out my other cave exploration vehicle. That made it into the chamber.

@@brickandgear Pls send link

@@gamingpro5471 ruclips.net/video/JxEJ13ms-WE/видео.html

@@brickandgear thks

😁

Thank you for watching and taking the time to connect! 🙏🙂

😐

Bro what in the world of goobers 😭

Thank you! 🙏

Great... 😁

Yes, this will work on any 2.4GHz controller. Be extra careful though. As the sub goes deeper, external pressure will increase and water will eventually go through the seals. It's inevitable and you'll have to be prepared to protect the motors and electronics.

Ok and can I use Ethernet cable instead or can I use any other cable

@@Prxjetej I don't know. When I did my research on transferring a 2.4GHz signal under water (Bluetooth or WiFi), they specifically mentioned using a coaxial cable and removing 6cm of shielding on each end. Something to do with the wavelength, so anything else will probably not work.

@@brickandgear ok👍

It's already in pieces! 😁

Thank you for watching and leaving a comment! 🙏 A bomb defusal drone is a good idea, but I have no bomb to defuse. 😁

Thank you! 🙏

It's probably my next project.

I would definitely change the transmission to make it more robust. On this boat, both motors turned the same axle that went all the way down to the propeller. If you check my latest video, I used the same transmission concept with a small tweak. Each motor turned its own axle that made its way down to the propeller, thus splitting the torque between the two vertical axles. This gave me the ability to utilize maximum power on the motors, thus achieving greater speed on an even bigger and heavier boat.

Thank you! 🙏

😁

Thank you! 😊🙏

Thank you for taking the time to watch and comment! 😊🙏

Thank you so much! 🙏

Thank you! A submersible that dives from the boat is a great idea, but I'll need an FPV system for that!

😁

You will! My dream is to build a huge boat that will steam down the river Acheron where the ancient Greeks believed Charon, the ferryman of the underworld, would carry the souls of the dead. It'll end up in the sea and sail to the cave of Persephone.

Huh? 😐

😆

Yeah... I got myself in trouble again. I'll have to build a "proper" carrier in the future, with an arrestor mechanism. My dream since I built my first boat : launching and landing an FPV drone, like the Parrot Disco, on the biggest LEGO carrier ever conceived. (need a much bigger budget)

Thank you for watching and sharing a comment! 🙂

That's really kind of you to say. Let's hope that through the hard work, the subscribers will come...

Launch and recovery, yes. Launch and landing... SpaceX... 😁 Some of the 3D printed boxes took a small amount of water, but nothing significant. It didn't affect the buoyancy or balance of the boat.

Thank you! I try to use whatever pieces I have available.

Thank you! 🙏

Thank you!